Learn How To Recondition Batteries at Home with Little Effort
Are you spending more and more of your hard earned money buying batteries for your car, laptop, mobile phone or any other gadgets every month? Do you need a battery for your alternative energy systems like wind or solar panels but find it too expensive? Do you have any drain or dead batteries at home?
Do not throw them! Recondition them instead.
One thing those battery companies don’t want you to know is that dead batteries can easily be restored to 100% working condition quite easily. New batteries are certainly not cheap! Why throw out old batteries when you can make them work again 100% for a fraction of the cost. Use it like its a brand new battery and save hundreds of dollars on batteries
If you are interested in learning everything there is to know about Reconditioning Batteries, then this is going to be the most important information you’ll ever read…”
Learn How To Recondition Batteries at Home with Little Effort And Almost No investment Whatsoever!
Dear friend, rechargeable batteries are everywhere, in your car, on your cell phone, in your cordless drill, and even in your solar panel system. And when they fail, they can ruin all the fun.
For instance, it doesn’t matter that your 2-year-old cordless drill is still in perfect condition. If the battery doesn’t hold a charge, a new Nicad rechargeable might cost even more than the actual drill!
But that’s peanuts compared to what you’d pay on deep cycle batteries. Think about it: if you want to go solar, be prepared to spend at least $1000 on your deep-cycle battery bank (and more often than not, upwards of $3k!) every few years!
It’s a mess. Here’s what it’s all about:
You don’t have to buy new, expensive batteries. Very few people know this: you can get discarded batteries for a few bucks or usually for free and then, using a very simple process and some inexpensive tools, you can recondition them and make them almost as good as new, in a matter of days!
Better yet: you can do this with almost any kind of batteries – from the small & medium sized Nicad and NiMH to the large capacity lead-acid batteries used in cars, forklifts, or solar battery banks.
It’s an amazing process that will extend the life of your batteries by a minimum of 50% to 70% and sometimes even more.
And if you know how to do it, and follow the proper “recipe”…
First, let’s take a look at why batteries fail. The number one enemy of batteries is sulfation. It is a failure mechanism in lead-acid batteries where sulfur crystals build up on the lead plates connected to the batteries. This results in insulation, thus preventing the cells to accept a charge. In comparison, NiCad batteries can last long compared to lead-acid batteries but both are subject to sulfation.
Types Of Battery That Can Be Reconditioned
Lead Acid Batteries – These are typically used in cars and trucks
Li-Ion Batteries – Laptop Batteries
Ni-Cd – regular rechargeable batteries
Ni-MH – Long life batteries. These are usually more powerful than others
How To Recondition Car Batteries
The battery is a rather expensive component of your car. Though they need to be changed only every few years, they are expensive… so why not learn to save cash on batteries that can easily be reconditioned at home?
If you are looking for money-saving guidelines regarding your car batteries, you need to know about car reconditioning. It’s been around for several years and it is an easy way of restoring your battery without leaving your pockets empty.
Research has shown that over 80% of to-be-thrown car batteries can be revitalized to over 95% of their original capacity. So stop throwing away your old car batteries, and start re-using them today!
9 Steps To Recondition Car Batteries
Step: Make sure you have the following materials needed:
A battery post cleaner.
Battery load tester.
Safety glasses and any protective gear.
Battery reconditioning chemicals.
Step: Clean the battery posts using a battery post cleaner. Take away the moist and other dirt from both posts on each side first.
Step: Check the battery’s voltage using a voltmeter. Your battery must have an average of at least 12 volts. If the battery has less than 12 volts upon reading, check the cells.
Step: Using a screwdriver, open the battery caps thoroughly for cell testing. Once the caps were already opened, hook the battery leads attached to the voltmeter. Avoid using the leads once it’s placed in the voltmeter since this will ruin the acid content from the battery cells.
Step: Put the positive lead on the battery’s positive post. The negative lead meanwhile must be placed on the battery’s first cell. Make sure that both leads will read two volts. After few minutes, place the positive lead into the battery’s first cell and the negative into the second cell. Repeat this pattern until you have reached the last remaining cells. Note: Your battery cells are weak if it has less than two volts.
Step: Plug the battery charger into the electrical outlet then place the batteries in the charger afterward. Make sure that the negative side of the batteries is placed along the charger’s negative marking and same thing with the batteries’ positive sides
Step: Hook up the positive lead from the battery pack. This is the first step in using the battery load tester. Once the positive lead is completely hooked, proceed to the negative lead. Make sure that your battery load tester can read at least 12 volts. Turn on the tester’s switch on and let it go after ten seconds. Also, make sure that the tester’s needle will not go beyond its reading up to 20 volts. Once you’re done testing, remove first the battery’s negative lead followed by the positive.
Step: Use the battery hydrometer in testing the first cell. You can do this effectively by placing the hydrometer’s end part into the cell. Carefully squeeze the hydrometer’s top before letting it go. Note: the float or fluid levels inside the glass tube must be in the green area. Charge the battery from scratch if the fluid has reached beyond the green area.
Step: Add the provided reconditioning chemicals in the battery using a plastic funnel. Place the funnel over the battery cell then pour over a tablespoon of chemicals into each cell. Charge the battery for not more than 24 hours.
Nickel-Cadmium batteries or often referred to as NiCad batteries are primarily used in gaming devices, appliances, and tools that require a rechargeable power source. These batteries, when reconditioned, help lengthen the expected lifespan, ensure safety from landfill risks and even save money. When a NiCad battery starts to recondition, the memories erased from the latter will enable a rechargeable battery hold for longer charging. Here are eight ways on how to recondition NiCad batteries.
8 Ways To Recondition NiCad Batteries
Don’t forget the following materials you need:
An old NiCad battery.
Battery tester or digital multi-meter.
Long-sleeved shirt or any protective gear. Don’t forget to include insulated gloves and safety goggles.
A 12-volt battery charger.
Check out the positive and negative ends of your NiCad rechargeable battery. The positive end is indicated by a plus sign while the negative end (raised in the flat) is indicated by a minus sign.
Use the battery tester (or digital multi-meter as an alternative) in testing the NiCad batteries. The testing is done in order to ensure that the batteries are fully discharged prior to its restoration process. The NiCad battery is fully discharged after usage or its functions enabled in many hand-held appliances such as digital cameras.
Wear any protective gear including the safety goggles and insulated gloves.
Start the battery reconditioning process by holding the black clamp attached to the 12-volt battery charger carefully.
Gently tap the NiCad battery’s positive end using the battery charger’s red clamp. This is done in order to enable the precondition of the battery’s memory.
Hold back in place the black and red clamps for three seconds before releasing them. Make sure that you’re not touching both clamps during this process.
Repeat the reconditioning process until the NiCad battery is fully charged.
As you begin your battery reconditioning process, these are a few tips To Note
Seek help or assistance from any person whom you know is professional in battery reconditioning. It doesn’t necessarily have to be a licensed electrician. It can be your relative or friend, as long as he knows the pros and cons of reconditioning. This tip is something to ponder if it’s your first time to recondition your battery.
Only recondition those batteries which can enable a rechargeable memory. Remember that not all appliances have batteries that are susceptible to reconditioning. Seek an expert for assurance of which batteries are allowed to be reconditioned.
Remove the NiCad battery’s “Dendrite Crystals” with the use of electric current. The dendrite crystals are essential in restoring the battery charger’s memory (or battery life in some cases).
Don’t rush while reconditioning your battery. Take a lot of time and most importantly, focus. Analyze first the proper way of holding the battery’s positive and negative ends. Be very careful when using the 12-volt battery charger. This is to ensure your safety from electric-related accidents.
Laptop batteries, just like the rest of the rechargeable battery packs, have chances of eventually losing its capacity to hold a full charge. However, the reconditioning process can be still done unless the cells from these batteries are replaced from scratch. Here are five ways on how to recondition laptop batteries.
5 Ways To Recondition Laptop Batteries
Insert the battery into the laptop first. Before doing this, make sure that your laptop is plugged into the electric circuit and is fully charged. Once you already inserted the battery, determine the laptop’s “battery light” indicator. Once the indicator is 100% charged, restart your laptop.
Disable your laptop’s hibernation settings temporarily. If you’re using Windows XP, click the “Start” button from the taskbar then click on the “Control Panel”. Click the “Power Options” button from the control panel then select the “Hibernate” tab. Uncheck the “Enable Hibernation” option then finally click “OK”.
Make sure that the battery is already discharged. In Windows XP, click the “Performance and Maintenance” options found in the Control Panel. Select the “Power Options” then “Power Schemes”. Under the Power Schemes option, enable its settings under the “Plugged In” and “Running on Batteries” by putting a small note. Set all the options to “Never” from its drop-down lists before finally clicking the “OK” button.
Unplug the laptop, but do not turn it off. The laptop must be turned on until the battery is 100% discharged. You’ll be able to find out if the battery is completely discharged once the laptop’s power or standby light automatically blinks or shut down.
Plug in the laptop after few minutes. Allow it to fully charge for the second time before restarting. Enable your laptop’s Hibernation and Power Scheme settings.
Laptop battery reconditioning is proven essential in prolonging the life of its cells. However, it is only proven in accordance with the techniques that are necessary to follow. The techniques are explained through these four tips.
4 Tips Laptop Battery Reconditioning
Determine the type of your laptop’s battery. The battery type is usually printed on its case. Most battery packs are made from Lithium-Ion (Lion), Nickel Metal Hydride (NiMH) or Nickel Cadmium (NiCd). Laptop batteries with Lion are more sensitive in reconditioning while the NiMH and NiCd ones can create a “reminiscence effect” when reconditioned.
Discharge the battery immediately. When you discharge your laptop’s battery in a matter of seconds, the terminals in the batteries start to utilize a “resistive circuit” effect, which is crucial in discharging the power stored from the laptop safely.
If possible, place the battery in the freezer. Put first the battery in zip lock bag in order to ensure its safety from any contact caused by moisture from the freezer. This is a unique yet hassle-free way of removing the battery’s unnecessary reminiscence effect.
Discharge and freeze the laptop’s battery again until its cells are 100% discharged. The number of times you discharge and freeze them, the higher chances of improving the battery life and its performance on your laptop.
Multi-tester is an ultimate tool in the electronics world. Using this tool, you will easily distinguish a battery if it is repairable or not so you won’t waste your time on batteries that can’t be reconditioned. Several techniques on how to test a dead battery for repair can be found in the EZ battery reconditioning course.
Making Extra Profits From Batteries
Aside from saving money on batteries, why not make profits from it? Now that you know how to recondition a battery, it’s time to share your new skill with your friends, office mates or neighbors and offer them your service.
You can also put a little signage in front of your house that you’re starting a battery reconditioning business. People want to save money, so they will surely come to you to recondition their batteries instead of buying a new overpriced battery in the market.
Our Top Pick For Battery Reconditioning
Teach you how to bring your old batteries back to life.
Save your money and NEVER buy a new battery again.
Earn you massive profits from your reconditioning skills by purchasing old batteries and reselling them.
Learn How To Recondition Batteries at Home with Little Effort
Aside from saving money on batteries, why not make profits from it? Learn How To Recondition Batteries at Home with Little Effort And Almost No investment Whatsoever!, it’s time to share your new skill with your friends, office mates or neighbors and offer them your service.